Technical
datasheet
mit Anschraubflansch, mit oder ohne Rastsperre
|
Catalogue
|
d1 Pin -0.02/-0.05
Bore +0.10/+0.03 |
l1
|
b
|
d2
|
d3
|
d4
|
k
|
l2
|
l3
|
l4
|
Spring load in N ≈
initial |
Spring load in N ≈
end |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
GN 817.1-6-6-B
|
6
|
6
|
13
|
23
|
4.3
|
34
|
22
|
48
|
22
|
6
|
6.5
|
19
|
|
GN 817.1-6-6-B-RT
|
6
|
6
|
13
|
23
|
4.3
|
34
|
22
|
48
|
22
|
6
|
6.5
|
19
|
|
GN 817.1-6-9-B
|
6
|
9
|
13
|
23
|
4.3
|
34
|
22
|
48
|
22
|
6
|
6
|
25
|
|
GN 817.1-6-9-B-RT
|
6
|
9
|
13
|
23
|
4.3
|
34
|
22
|
48
|
22
|
6
|
6
|
25
|
|
GN 817.1-8-8-B
|
8
|
8
|
16
|
28
|
5.3
|
38
|
26
|
58
|
26
|
8
|
8.5
|
26
|
|
GN 817.1-8-8-B-RT
|
8
|
8
|
16
|
28
|
5.3
|
38
|
26
|
58
|
26
|
8
|
8.5
|
26
|
|
GN 817.1-8-12-B
|
8
|
12
|
16
|
28
|
5.3
|
38
|
26
|
58
|
26
|
8
|
8.5
|
28
|
|
GN 817.1-8-12-B-RT
|
8
|
12
|
16
|
28
|
5.3
|
38
|
26
|
58
|
26
|
8
|
8.5
|
28
|
|
GN 817.1-10-12-B
|
10
|
12
|
16
|
28
|
5.3
|
38
|
26
|
58
|
26
|
8
|
9.5
|
38
|
|
GN 817.1-10-12-B-RT
|
10
|
12
|
16
|
28
|
5.3
|
38
|
26
|
58
|
26
|
8
|
9.5
|
38
|
|
GN 817.1-6-6-C
|
6
|
6
|
13
|
23
|
4.3
|
34
|
22
|
48
|
22
|
6
|
6.5
|
19
|
|
GN 817.1-6-6-C-RT
|
6
|
6
|
13
|
23
|
4.3
|
34
|
22
|
48
|
22
|
6
|
6.5
|
19
|
|
GN 817.1-6-9-C
|
6
|
9
|
13
|
23
|
4.3
|
34
|
22
|
48
|
22
|
6
|
6
|
25
|
|
GN 817.1-6-9-C-RT
|
6
|
9
|
13
|
23
|
4.3
|
34
|
22
|
48
|
22
|
6
|
6
|
25
|
|
GN 817.1-8-8-C
|
8
|
8
|
16
|
28
|
5.3
|
38
|
26
|
58
|
26
|
8
|
8.5
|
26
|
|
GN 817.1-8-8-C-RT
|
8
|
8
|
16
|
28
|
5.3
|
38
|
26
|
58
|
26
|
8
|
8.5
|
26
|
|
GN 817.1-8-12-C
|
8
|
12
|
16
|
28
|
5.3
|
38
|
26
|
58
|
26
|
8
|
8.5
|
28
|
|
GN 817.1-8-12-C-RT
|
8
|
12
|
16
|
28
|
5.3
|
38
|
26
|
58
|
26
|
8
|
8.5
|
28
|
|
GN 817.1-10-12-C
|
10
|
12
|
16
|
28
|
5.3
|
38
|
26
|
58
|
26
|
8
|
9.5
|
38
|
|
GN 817.1-10-12-C-RT
|
10
|
12
|
16
|
28
|
5.3
|
38
|
26
|
58
|
26
|
8
|
9.5
|
38
|
Führung
Zink-Druckguss
kunststoffbeschichtet
schwarz, strukturmatt
Stift
Edelstahl nichtrostend, 1.4305
Griff
Kunststoff (Polyamid PA)
Rastbolzen GN 817.1 Form C werden eingesetzt, wenn der Raststift zeitweise nicht vorstehen soll. Hierzu wird der Knopf nach dem Einziehen des Stiftes um 90° gedreht. Durch eine Rastkerbe wird der Knopf in dieser Position gehalten.
